Renegade
|
|
|
2008
Renegade 8
1. Stock Autos only, except as stated!
2.Any American made car. No jeeps, 4x4, station wagons. Minimum wheel base 101".All sheet metal must be stock,may make doors from sheet metal Aluminum
. Fenders and quarters must use factory tops bottom may be made from sheetmetal.OR ,Aluminum.
3. Gutting, hood, and trunk OK, homemade radiator support, aluminum radiator OK. Boxing interior OK.
Boxing interiors OK. Interior spoiler can be no higher than dash .After market nose and bumper cover legal.
May run 6”x 60” spoiler must be self supporting, may not go over side of quarter panel ,no spill plates.
4. Fender wells may be cut for tire clearance, but not excessive.
5. Front and rear inner fenders may be removed.
6. Fuel cell mandatory.
7. All glass and chrome must be removed.
8. Suspension must be stock. May run racing springs with adjustable buckets. One 2” lowering block maximum
each side. Top A-Frame can be cut. Aftermarket bushings in A- frame and trailing arms ok.Tube type non-adjustable top a-frames OK.
Top trailing arm may be cut for pinion angle only. Leaf spring cars may adjust perches for pinion angle.
9. Rear shackles may be aftermarket holes must in same location both sides with no extra holes
10. Positive traction, limited slip, or locked rear ends allowed.
11. Full spool ok. Mini spool OK
12. Automatic transmission torque converter.min.11 in. stock type May run transmission cooler.Staight drives cast iron 3 speeds only with an 18 Lbs.(@)3400lbs,14 Lbs. flywheel (@)3500 lbs lbs. mininum clutch stock type.
13. Any steel motor mount OK. Cubic inch 363 max.
14. Rear end:Chevy any gear ratio , Ford 9" ok in all cars 6.20 gear max. Aftermarket axles both sides ok.
15. Tires 70 series street tire. Wheels and tires max. Width 8”. Bead lock right rear only. Any offsets, wheel spacers ok.
16. Engine must be in stock location
17. Racing removable steering wheel allowed and recommended.
18. Stock rods, may change rod bolts, only grinding for balancing. Any 5.7 stock appearing rod ok. (i.e. eagle SIR, Scat I-beam).Floated wristpins OK. No small journal rods (2.000) in a 350 motor.
19. May remove all A/C, smog pump, and power steering.
20. Large wheel studs and lug nuts OK.
21. Hydraulic cam and lifters only max. lift.425.at valve. valley pan ok. No bottoming of lifters, will be teched and determed by techman. Adjustment of loosening rocker arm will be done by techman.
22. Pistons must have a four (4) valve relief. No two eye brow piston with scratches. Chev. .100" deep Ford .040" deep eyebrows.
23.Heads- no 461, 461X, 041, 186 or 492 castings. No Vortex heads! No closed chambered heads allowed .Pin studs in heads ok .Screw in studs ok, Guide plates ok. Rocker arms stamped steel 1.5 or 1.6 ok.
24. Carburetor: Quadrajet. No modifications except choke flap removal. No removal of choke horn. Any air cleaner must not protrude through hood.
May run Holley 600 cfm #1850 carb. must be stock appearing on outside with stock tube and float bowl. Must have air horn with number. Adapter plate Mr. Gasket #1932 only 3/4" thick may run the 1/4" Q-jet gasket. May run a box stock 650 Holley #4777. May use a 1" max thickness adapter if using Holley carb on Q-jet intake with two .070" max thickness gaskets only. (NO Holley pattern factory intakes.)
25. Valve size- Maximum 1.94 intake, 1.50 Exhaust.Stock size for other makes.
26.Crankshaft- Any stock appearing, may use 305 in a 350, 48 lbs. mininum cast, 50 lbs. mininum steel, may balance by drilling only, no other modifications. Journals can be turned a maxium of .060" .
Big oil pan allowed
27. Headers ok, must exit parallel to ground
28. Any timing chain, no belt or gear drives.
29. Weight- 3400lbs with driver after race.
30. Maximum .060 overbore.
31. Block- May strap or use studs.Deburring and screens OK.
32. Protest any 3 items except bottom $300.00, Bottom end $600.00 accepts fee $100.00
track retaining $100.00.
32. Fuel: Pump gas or racing gas. NO ADDITIVES
|
|
|
Posted by Teems
|
|
|
